design method的例句大全

Discussion about the Optimization Method of Exterior Ballistics Design for Winged Rockets

尾翼式火箭弹外弹道优化设计方法的讨论

互联网摘选

The Gun Interior Ballistics Design Method Based on Two-phase Flow and Application in New Charge

基于两相流理论的火炮内弹道设计方法及其在新型装药设计中的应用

互联网摘选

The comprehensive first-aid repair capability is regarded as one of the important indexes to evaluate systemic design method of ship.

综合抢修性能是衡量舰艇系统设计方案的重要指标之一。

互联网摘选

The optimization design method can also be used in the balance of non-sinusoidal changing load resistance moment and has important value of application popularized.

对非正弦变化的负载阻力矩的平衡也可应用本设计的优化方法，有推广价值。

互联网摘选

The paper presents a design method of EMI mains filter and some points needing an attention in application.

介绍EMI电源滤波器的设计方法以及在使用过程中应注意的问题。

互联网摘选

Design of Chamfer Tool and Its Sharpening Calculating Method

齿轮倒角刀的设计及刃磨计算

互联网摘选

Optimization of corona ring design for EHV composite insulator using finite element and neural network method

基于有限元和神经网络方法对超高压合成绝缘子均压环结构优化的研究

互联网摘选

This design method can improve dynamic and static characteristics of system by collecting bending force signal, summarizing experience and designing control rule.

通过采集弯曲力的变化信号，总结弯曲经验，制定控制规则，改善了系统的动静态特性。

互联网摘选

According to the law of crack development and mechanical index correlation analysis results, use the maximum bending force, shearing force and fracture energy as the main mechanical parameters, put forward the test design method.

基于裂缝动态发展规律与力学指标关联度分析结果，以最大弯曲力、层间剪切力和断裂能作为主要设计参数指标，提出配合比设计的试验方法。

互联网摘选

Secondly, separate the system into dc biasing circuit, filter circuit, linearization technology, cooling technology, and broadband matching network. In detail describe the function, circuit structure, and design method of each module.

其次，将系统分为偏置电路、滤波电路、线性化技术、散热、以及宽带匹配网络等模块，详细叙述了每个模块的作用、电路结构和设计方法。

互联网摘选

In this paper, the calculating formula for biaxial load reinforced concrete column with rectangular section and the design method in engineering practice are analyzed.

本文分析了矩形钢筋混凝土柱在双向受压作用下的计算公式以及工程设计中常用的方法。

互联网摘选

Systematic design method of fuzzy controller based on Popov stability criterion

基于波波夫稳定判据的模糊控制器系统化设计方法

互联网摘选

Combining with the optimality criterion method and the bi-factor algorithm, the inverse eigenvalue problem for optimal Parameters design of elastic mechanisms is solved effectively.

采用最优性准则方法，给合结构优化设计中的双因子算法，有效地解决了给定弹性机构某几阶固有频率时设计构件截面参数这类逆特征值问题。

互联网摘选

In this paper, the generalized optimality criterion is first employed in the design of reinforced concrete frames and a so called "group by group searching method" which identifies active constraints from all contraints, is proposed.

本文首次采用广义最优性准则设计钢筋混凝土框架，并建议一种区别有效约束和无效约束的方珐，名为分组穷举法。

互联网摘选

This paper describes an efficient optimality criterion method for the optimum design of antenna structure.

本文提出了一种有效的结构优化方法&导重准则法。

互联网摘选

A new method in design of arbitrary order analog fractance circuit based on binomial expansion is presented.

提出一种通过二项展开式设计任意阶模拟分抗电路的新方法。

互联网摘选

The design of parallel algorithms by the bisection technique for solving the tridiagonal linear system of equations, which involves the parallel forward and backward sweep method, odd-even elimination, odd-even reduction, block elimination and so on, are discussed.

本文讨论用二分技术设计求解三对角方程组的并行算法，其中包括并行追赶法、奇偶消元法、奇偶约化法和块消元法等。

互联网摘选

By introduction of the basic concept, design philosophy of the neutral earthing, and the method of integrating theory with practice, why the neutral earthing with blowout coil for the Three Gorge 35 kV electric distribution network and specific connection measures are taken are described.

该文通过介绍中性点接地的基本概念、设计思想和理论联系实际的方法展开分析与研究。阐明了三峡35kV配电网络中性点采取消弧线圈接地方式的原因及解决其接线的具体措施。

互联网摘选

The analysis taking booster charge design of columnar explosive device as the example shows that parameter selection method of booster charge is feasible.

以柱形爆炸器传爆药柱设计为实例，说明此套传爆药柱参数选择方法是可行的。

互联网摘选

The low-level constraint relational model was introduced to record various constraint relations among parts and to check, improve and complete the reconstruction of the final assembly model, executing the result-oriented bottom-up design method; the parametric!

通过引入低层次的约束关系模型记录零件之间的各种约束关系，检验、改进和完成最终装配模型的重建，实现自底向上的面向结果的设计方法；

互联网摘选